loading

One-stop Linear Motion Products and Linear Motion Solution Provider. 

Linear Guide Part Numbers: What the Code Actually Tells You Before You Order

Every linear guide block carries a spec sheet compressed into a code — series, size, mounting style, preload, sealing — and most ordering mistakes we see are compression errors: someone read the code as a name ("the 25mm one") instead of as a sentence ("the 25mm flange block, light preload, standard seals, from this family").

Linear Guide Part Numbers: What the Code Actually Tells You Before You Order 1

Reading the code properly does two things for you. It lets you order a replacement with confidence even when the old block's markings are half worn. And it tells you, before any money moves, whether a cross-brand substitute is genuinely equivalent or just dimensionally nearby. This guide walks through how the three designations you meet most often — HIWIN, THK, and Rexroth — are built.

The Anatomy Every Part Number Shares

Whatever the brand, the code breaks into four positions:

  1. Series family — the letters that say which product line the block belongs to, which implies the ball or roller design and the precision class options.
  1. Size — almost always the rail width in millimeters: 15, 20, 25, 30, 35, 45 and up.
  1. Block style — a letter or code for flange versus square, and sometimes height variants.
  1. Suffix — preload, seals, and special configurations, packed into the letters or digits at the end.

The series and size are the parts everyone reads correctly. The expensive mistakes live in positions three and four.

Reading a HIWIN Code

Take HGH25CA and read it as a sentence:

  • HG — the heavy-load ball series, the standard for machine tools and automation.
  • H — flange type block (a W here would mean square type).
  • 25 — runs on a 25 mm wide rail.
  • CA — the preload and seal configuration bundle.

The last position is the one people skip, and it is where "the block fits but the machine feels different" comes from. Two blocks of the same size and family with different end letters will grip the rail differently — one tight, one loose — and on a four-block axis, mixing them shows up as a corner of the table that sits differently than the other three. When you order from us, send the complete code including that tail; a size alone is not a specification. The block-shape letters deserve their own reading — H marks a flange block, W marks a square one — and mixing them up produces the classic "it fits the rail but will not bolt down" arrival.

Reading a THK Code

THK codes follow the same logic with different letters. In HSR25A:

  • HSR — the series family.
  • 25 — the rail size in millimeters.
  • A — flange type shape; B marks the square type.

The letters after the shape code cover seals, ball complement, and special specs — and THK's full designations can run longer than most, with appended codes for each option. The practical rule for THK is the same as for every brand: the further right you truncate the code, the more specifications you are silently discarding. Match the full string, or match by measurement plus duty description.

Reading a Rexroth Code

Rexroth blocks look different because the code is numeric: R165121420. The leading R16 family marks the runner block line; the digits that follow encode the size class and then a run of configuration digits covering preload, seals, and variant details.

Two things matter with numeric codes:

  • Position is meaning. In a letter-coded brand, a wrong letter is visible — "CA" versus "CC" reads as an obvious difference. In a numeric Rexroth code, a single transposed digit can change a real specification while looking perfectly plausible. Copy codes character-for-character, never from memory.
  • The full string is the spec. For a code like R165121420, the trailing digits are not decoration — they are the difference between two blocks that bolt down identically and run differently. When a nameplate is gone and you are rebuilding from measurement, tell the supplier the size class and let them confirm the configuration digits against the machine's duty.

Cross-Referencing Without Guessing

Once you can read the four positions, cross-brand substitution becomes a deliberate decision instead of a gamble. What actually transfers between brands at the same size:

  • rail width and mounting-hole pitch (usually),
  • block envelope in flange or square styles (usually),
  • precision grades (mapped by grade class, not by letter name).

What does not automatically transfer:

  • preload class — every brand grades it differently, and the feel under hand pressure is the tell-tale;
  • seal configuration — a standard seal on one brand is not a reinforced seal on another;
  • grease channeling and lubrication intervals.

So the honest cross-reference procedure is: measure the rail (width and hole pitch), photograph the block's top face for the mounting style, capture whatever remains of the original code, describe the axis's duty — and let the supplier map the three brands' classes against each other. Dimensional interchange is common; specification interchange has to be confirmed, not assumed.

FAQ

Can I order a replacement block using only the size, like "a 25mm linear guide block"? You can, and you will receive a 25mm block — possibly the wrong style, preload, or seal for your axis. The size is one of four positions; order with all four filled in.

Do the same letters mean the same thing on different brands? No. A "W" or an "A" means one thing in one family and something else in another. Never carry a suffix across brands by letter — carry it across by what it does (preload class, seal type).

The nameplate on my old block is unreadable. What do I send the supplier? Three things: rail width and mounting-hole pitch, a top-face photo of the block showing the bolt pattern, and a sentence about what the axis does and how the old block failed. That is usually enough to reconstruct the full designation.

The Short Version

A part number is not a name — it is a spec sheet, and every character you drop from it when ordering is a specification you silently gave up. Read the four positions: family, size, block style, suffix. Copy numeric codes character-for-character. Cross-reference by measurement and duty, not by letter-matching.

If you are holding a block with a half-worn code right now, send us the photo and the measurements — we stock HIWIN, THK, Rexroth, Schneeberger and TBI lines, and we will read the code with you before the order goes out.

prev
How to Choose a Ball Screw Supplier: 7 Things to Check
recommended for you
Get in touch with us
Customer service