Most ball screw enquiries arrive with a diameter and a lead, and nothing else. The quote that comes back is accurate to what was asked — and then the shaft ends do not match the support units, the preload is not what the axis needs, or the accuracy class exists only in the product title.
The drawing is an engineering question. The supplier is a documentation question: what can they put in writing before the order, and what arrives with the part. Here are seven checks we would want on the table before an RFQ goes out.
There are two separate decisions in a ball screw purchase. The first is which screw fits the axis — size, lead, accuracy, preload, mounting. That is covered in detail in our guide to linear guide rail replacement, where the same measurement-first logic applies, and in ball screw play and what to confirm before ordering a replacement for axes that have lost repeatability.
The second decision is whether the supplier can supply that screw as specified, with evidence. The checks below are about the second one. They apply whether you are buying an original branded component, a same-size cross-reference, or a custom-machined screw.
"SFU1605" or "32 × 10" is the start of a part number, not the whole thing. A complete designation normally encodes the nut form, the number of ball circuits, the accuracy class, the preload or axial clearance, the direction of the lead, and the shaft-end machining. Two screws with the same diameter and lead can behave differently on the same axis.
Ask the supplier to write out the full code they intend to ship, and put that code on the order. If you are replacing an existing screw, the markings on the old part or the machine's spare-parts list are the source of truth; a photograph of the nut and the end machining resolves most ambiguity. Where a ready-made assembly is what you need, a ball screw set with end machining, nut housing and support units makes the whole code visible in one line item.
Accuracy class is written into the designation, and it should also be documented. Ask specifically what measurement record comes with the screw — for example, a lead-error measurement over the usable travel — and how the stated class was established.
This matters more on a positioning axis than on a transport axis, and it is where a low quoted price can quietly change the product. Rolled screws and ground screws are supplied in different accuracy ranges, and a C7 rolled screw is a different part from a C5 ground screw even when the diameter and lead match. If the class matters to the machine, treat the record as part of the order rather than a favour. Our notes on what to settle before asking for a price make the same point from the type-selection side.
When the order names a brand — HIWIN, THK, Rexroth, Schneeberger, TBI — the question is not only whether the part fits, but whether you can confirm what was delivered. Ask for:
These are ordinary documentary checks, and a supplier handling branded stock should be able to provide them without friction. They are also the checks that are hardest to run after the part is installed and the packaging is gone. For a specific example of how branded ball screw designations read, see the HIWIN 2505 ball screw entry in our catalog.
A screw cut to the wrong end dimensions is not a returns problem; it is a scrap problem. Before production starts, get a drawing that shows the journal diameters on both ends, the length of each machined section, any keyway, the thread and retaining details, and the overall shaft length with the nut position marked.
Cross-check that drawing against the support units and coupling you actually have. The fixed end and the supported end are usually machined differently, and a drawing that shows them as identical is worth questioning. If the assembly includes the SFU series screw used on CNC machines and industrial robots, confirm whether the nut housing and BK/BF supports ship as matched parts.
Preload is where two otherwise identical screws feel different in the hand. Ask what preload class or axial clearance applies, whether the nut is single or double, and what the specified backlash or axial clearance figure is. Ask also how that value is measured.
On a reversing axis, this is a positioning specification, not a comfort preference. A screw quoted without a preload class will be shipped at whatever the supplier's default is, and that default may not suit an axis that reverses under load. If the old screw is being replaced because the axis stopped repeating, read the play diagnosis guide first — the lost motion is not always in the nut.
Beyond the accuracy record, a supplier should be able to say what was checked and what documentation travels with the part: shaft material and heat treatment, surface hardness where relevant, the dimensional inspection of the end machining, and the running check of the nut on the shaft.
None of this requires special pleading. It is the normal content of a technical delivery for a precision component, and it gives your incoming inspection something to check against. If the answer is "the parts are checked" with no record, ask which dimensions were measured and where the results are kept. The same discipline applies to a linear module built around a screw — the module's repeatability figure is only meaningful alongside the screw's own specification.
Before the order, settle the process rather than the outcome: who confirms the drawing, at what point the confirmation is recorded, and what the route is if a delivered part does not match the agreed designation or end-machining drawing. Ask whether the supplier will re-machine, re-supply, or credit the item, and what evidence they need to start that conversation.
This is also the point to clarify technical support after delivery — who answers a question about preload or support bearing arrangement once the screw is on the machine. A supplier who will put the full designation, the drawing and the inspection record in writing before the order is usually the same one who answers afterwards.
Pulling the seven checks together, an RFQ that can be quoted accurately contains:
|
Item |
What to send |
|
Full designation |
Complete code, including accuracy and preload class |
|
Shaft |
Diameter, lead, overall length, handedness |
|
End machining |
Dimensioned drawing for both ends, keyway, supports and coupling |
|
Load and duty |
Axial load, speed, duty cycle, orientation (horizontal or vertical) |
|
Environment |
Coolant, dust, washdown, temperature |
|
Documentation |
Accuracy record, inspection data, traceability requirements |
|
Brand decision |
Original branded part, same-size cross-reference, or compatible |
|
Quantity and timing |
Required quantity and the date the parts are needed |
Eight lines, and they remove nearly all of the back-and-forth that turns a simple enquiry into a long exchange. If you do not have the full designation, send a photograph of the old part and the dimensioned end drawing — that is enough to start.
We carry branded linear motion components and compatible equivalents alongside custom machining and processing. Send the RFQ list above and we will confirm the designation, the drawing and the documentation before anything is cut.
What should I include in a ball screw RFQ? Include the full designation, shaft diameter and lead, overall length, a dimensioned shaft-end drawing, the axial load and duty cycle, the operating environment, the required documentation, and whether you want an original branded part or an equivalent.
How can I verify an original branded ball screw? Ask for photographs of the original packaging and label, the laser-etched code on the part, the batch identifier, and a written statement of whether the item is the branded original or an equivalent. Check these on arrival, before the packaging is discarded.
Why is the full designation more important than diameter and lead? The full code also carries the nut form, accuracy class, preload or axial clearance, and shaft-end machining. Two screws sharing a diameter and lead can differ in reversing accuracy and in whether they mount to your supports.
What documents should arrive with a precision ball screw? At minimum, the accuracy or lead-error record for the stated class, the dimensional inspection of the end machining, and the material and heat-treatment information. Ask which of these are supplied before placing the order.
Can a supplier cross-reference a branded screw by size alone? A same-size cross-reference is often dimensionally possible, but the mounting-hole pattern, preload class and end machining still need to match. Cross-reference by measurement and by the full designation, not by brand memory.
Should I choose an original branded part or a compatible replacement? Both are legitimate. Decide based on availability, the documentation you need, and the machine's duty — then make sure the chosen route is written into the order so the preload class and machining travel across.